Customer Reviews for VEVOR Mobile Base, 680.3 kg Capacity, Adjustable from 527 x 603 mm to 711 x 850 mm, Heavy Duty Universal Mobile Base Stand with Swivel Wheels, for Woodworking Equipment, Bandsaw, Power Tools, Machines

This was one of the worst products that I have purchased on the Internet. I did quite a bit of research and read other reviews. The products directions were an absolute joke and clearly not sufficient to properly assemble the product after hours of effort to make this put this product together, I gave up, disassembled it, and threw it away. By the way, I tried several times to get assistance from the manufacturer, but to no avail. I strongly recommend against your buying this poorly made poorly manufactured and machine, and utterly disappointing product save your money or just flush it down the drain like I did .

This mobile base for use with my table saw was straightforward as to the plywood that needs to be supplied and cut to size. However, any of the threaded holes have the threads filled with paint making it difficult to put in the supplied screws and bolts. I would recommend that all fasteners be driven into the threaded holes before you are to the point for actual assembly. A couple of the threaded holes/fasteners would not thread together without threads stripping. This caused a lot of extra work by replacing the bolts and nuts as well as tapping the holes to fit. Be aware that all of the threads and sizes are metric. It would have been helpful to have a 10mm tap to repair or clean out any threaded holes that are not the correct size to fit the bolt supplied. One of the 10mm bolts was quite severely bent. Customer service department asked for pictures of the defects and problems that I encountered and gave a partial refund that helped pay for the extra supplies and tools that should have not been needed for the customer to supply to fix the machining that was done poorly in the metal. The material frame pieces are strong and the casters are good. Instructions could have been a little more detailed pointing out areas to watch out for when assembling.

The steel is nice and heavy the blots could be better. Just a bag full of nuts, bolts and a lot of trial and error guess work. Which nut? Which bolt? Which part goes where? When I was all done the lifting casters did not work and doesn't work. I guess the star rating is not worth much at this point. I will not be buying for my other tools, I'll something else.

Used on a band saw that may way 200 lbs. so this 700lbs capacity should be overkill. The frame is well made but the wheels just do not roll well saw is just barely easier to move than just scooting across the concrete. I was expecting more movability

This does its job. It fit the frame well of the Jet supersaw and held up to the weight. This is built on the cheap side. The leg lock cams are horrible but will function for a little bit. Overall well worth the money.

Value for money in relation to comparable products. Strong adjustable steel construction which is ideal for moving a bandsaw. Relatively straightforward to assemble but the many 13mm nuts and bolts need tools rather than “snap together” or using a screwdriver as suggested! The paintwork on the locking lever was badly marked (see photo) and the screw holes for the levelling feet were blocked with paint which had to be re threaded with a bolt before fitting. Disappointing as the product is generally well made and does the job.

These are good wheels, but the assembly manual is a bit vague, and getting it setup with the adjustable feet was fiddly. Also two of the screws didn’t want to thread into the holes. It took a little coaxing. It comes with two different length screws to attach the wheels to the plywood. I had 1/4” plywood. They probably wanted you to use 1/4” or 3/4”, so the screws poked too far out the bottom. I was worried they’d scrape on the ground on the fixed wheel side, so I trimmed them with a Dremel and cut off wheel.

Order was missing parts so sent a replacement that also was missing parts. Able to cobble together but did need to purchase device to tap two holes ($10) that were not cleanly machined. They provided a full refund, which was nice, and made me feel whole. Customer Service does take a few days, so you need to be patient.

HELPS N A SMALL SHOP

I purchased two of these. One for a band saw and one for a table saw. Assembled well enough, allows for easy leveling and easy movement. I can now put away easily when not in use. Both that I received were missing the kickers to put the travel wheels down. Works fine without but if it’s to be included it should have been.