Customer Reviews for VEVOR Digital Ultrasonic Cleaner 30L Ultrasonic Cleaning Machine 40kHz Sonic Cleaner Machine 316 & 304 Stainless Steel Ultrasonic Cleaner Machine with Heater & Timer for Cleaning Jewelry Glasses Watch

This cleaner does a great job on everything I've thrown at it so far.It does take a while to heat up so plan accordingly. From room temperature to about 140 C takes about 45 minutes to an hour, not a problem if you flip it on and go about your business while it warms.I got a couple 2.5 gallon containers of water for about $3.00 each, used the water to mix my solutions then I have a place to drain the solution back into in between jobs.

Everything worked as it should, just wish it would heat up quicker.

Solid and well built . Put small items in the basket they give you or get a basket that will hold your small items . They will fall into the drain and go out through the drain when you empty it .

works ok, does a nice job cleaning my airbrushes.

This product was delivered on-time and appears to work as advertised. I have used it a few times and have had no problem. My only concern is durability which only time can determine if it continues to work over time. Yes, I would recommend this product.

I've been using it daily in my tattoo shop for a few weeks now. It runs great, cleans great, and is easy to empty thanks to the valve on the side. Everything I ned in an ultrasonic cleaner.

No fill line was the ONLY question I had, but it didn't matter. This machine works so well, a must have for 3D resin printing. Bigger than expected. Has a tea ball cage for small items. Quieter than expected.

Cleaned my Choke tubes.

I purchased the 3.2L unit. It arrived today and I tried it on a few things. Used car signal switches are always caked up with gunk which I suspect is dead skin, oils from hands, and dirt. I can't sell them looking like that. I usually have to use a toothbrush on them and it's a real pain to get them clean. Anything other than plain hot water will take the symbols off, so no detergents. The ultrasonic cleaner had them looking brand new in about 20 seconds with just plain hot water. Of course, I can't submerge the entire switch because the electronics could get damaged, but the cleaner does the hardest part. I also tried it on my glasses. If you have painted metal frames, don't do it. Fortunately, I tried it on my old pair. It took the paint off and now they look like chrome. They are very clean though. I was surprised by the size. It's smaller than I expected, but it will work for what I need it for. My suggestion would be to get one size bigger than you think you need. The instructions are useless. They're poorly translated and say something about turning knobs to adjust time and temp. There are no knobs, it's push button. Overall, I would say it's worth the money and I would definitely recommend it.

I purchased the "Mophorn 3.2L Professional Ultrasonic Cleaner 320W 304 and 316 StainlessSteel Digital Lab Ultrasonic Cleaner with Heater Timer" to clean 3d prints from my new AnyCubic Photon S resin printer. I use the printer primarily to create tabletop war gaming miniatures.While the first 20-30 miniatures that I printed (using Anycubic's resin which shipped with the printer) were good, they lacked the detail present when I viewed the STL file in Chitubox. After printing, I was cleaning the miniatures 0.99% isopropyl alcohol, but the features appeared "soft" after priming them (airbrush 50% thinned, Vallejo white primer). I tried a longer exposure time and heating the room in which the printer was operating to 80 degrees F in the hopes that the resin would thin and somehow capture more detail.That's when I turned to YouTube and learned what "everyone" else was doing to get better prints: cleaning the newly printed miniature with an ultrasonic cleaner.Being before Christmas, the 2L cleaners were sold out, but I'm glad I went with the 3.2L model. The basket is the perfect size for the 4-8 miniatures that I can cram onto the Photon's build plate. It fits all of my prints, but I'm not wasting a lot of alcohol for unused space.The first miniatures out were markedly improved! Small facial details were more pronounced and the entire model just appeared "sharper". Using the same priming method it was as if I were using a different printer.My guess of what was happening is this: as the resin miniature is printed, it is continually "bathed" in the resin and then exposed to air for the 5-7 hours that a build required. Even though it was cured, the syrupy resin was air drying in all of the cracks and crevices, obscuring the details. Simple cleaning in 99% isopropyl alcohol was not sufficient.I cleaned the miniatures in the ultrasonic cleaner directly in the basket (not using a sandwich bag as I've seen others suggest) using the isopropyl alcohol (as I'd purchased a "flat" of it here on Amazon thinking it was my best option). Anecdotally, the results were good, but I got better results using a 50-50 mixture of Simple Green and water. And its stinks less than the alcohol. The Simple Green does leave the miniature feeling "tacky" though, so I often just swish them around in an old plastic container of alcohol. This seems to remove the tackiness from the Simple Green.After cleaning, I then harden the miniatures in a UV nail curing station ("36W UV Nail Lamp Dryer MelodySusie UV Gel Nail Polish Curing Light Professional Nail Art Lamp with 120s, 180s, 30min Timer Setting") which I also picked up on Amazon. There's no going back.On the down side, my $320 Photon S printer actually costs an extra $130 ($100 for Ultrasonic cleaner, $30 for UV lamp) but the end results are breath-taking.OK, concerning this ultrasonic cleaner...I've never owned one before so I have nothing to compare it to. That being said, it is solidly constructed from stainless steel, and the switc