Pulse Sparkle Spot Welder 400w Gold Silver Platinum Jewelry Welding Machine
Rated 3.5/5 based on 11 customer reviews

Pulse Sparkle Spot Welder 400w Gold Silver Platinum Jewelry Welding Machine

Available: Out of Stock
Product SKU: 50ASSDHJ000000001V3
$219.99 AUD
Successful pre-order.Thanks for contacting us!
You should make sure that the power voltage is suitable for this equipment before using it. The welding output wire should be connected to the screw on the corresponding polarity (The nut should be tightened when output wire is connected to the output pole). When the welder is working, you should use the clip on the output wire clamp the workpiece, close to the tungsten needle. The distance between tungsten needle and the workpiece depends on the size and shape of the workpiece, it is usually between 0.5-1 mm. Set the welding position and move the foot switch, the high-temperature electric arc between the workpiece and the tungsten needle are welding the workpiece. The discharge end of the tungsten needle must be kept sharp before using and during using to maintain a good discharge condition. According to the size of the workpiece, the size of solder joints and technological requirements, you can change the output pulse current intensity to achieve the desired effect (the machine can be welded 0.5-2.5MM). Depending on the size of the workpiece, the size of solder joints and technological requirements, you can change the output pulse current intensity to achieve the desired effect (the machine can be welded 0.5-2.5MM).For example, the potentiometer output pulse current increases in counter- clockwise direction. Otherwise the output pulse current decreases.

Sparkle welder can be used to weld:
1. Precious metal alloys; gold, silver, platinum and palladium
2. Titanium and stainless steel.
3. With some limitations, aluminum, tin and most brass alloys
4. Alloys with different attributes that are incompatible in normal welding
5. Alloys that would oxidize during welding and thus require an inert(Argon) atmosphere

Sparkle welder which use for jeweler:
1. Precisely position parts by tacking with the spot welder
2. Welding of necklaces with a diameter 0.3mm or larger(smaller diameter may melt)
3. Repair metal joints or breaks without removing set stones or pearls
4. Repair heat sensitive metals or metal alloys
5. Repair surface or entry point of a molding of the same alloy

With the inert argon atmosphere, welding can be done without requiring fluxing. The soldering point is smooth and does not require scaling or scale removal.

Installation and testing:
1. Connecting electrode, black wire to black connection (ground/cathode), red wire to red connection (positive /anode).
2. Connect argon gas through the argon gas pressure reducing valve; adjust the gas pressure reading to the minimum
3. Tungsten needle can be sharpened by grinding on the grinding wheel, or with the use of a Fordham flex shaft or dremal tool and an abrasive disk. Note that you should not use a wheel previously used to grind iron/steel as this will contaminate the needle and cause an uneven spark and/or weld results.
4. When installing the tungsten needle, please insure that the needle is approximately 5mm out from the welding head. The diameter of needle should be 0.1mm.

Our machine can only work with small things like necklaces with a diameter including or less than 1.2mm . No more than 1.2mm can work with metal like gold, silver, copper, steel, iron exclude aluminum.

Operation steps:
1. Plug the device into the wall socket and turn it on.
2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material.
3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow.
4. Clamp the object to be welded with the negative ground electrode. You cannot short circuit the machine by having both the tungsten needle and the ground clamp in contact through the work piece at the same time. Do not have the target work piece in direct contact with the tungsten needle. A 0.5mm arc gap is necessary for pulse welder operation. This is the optimum distance for welding.
5. Insure you have arc welding eye protection in place. The arc emits short wave UV radiation that will cause eye retinal burns and skin burns. Cover exposed skin (a shirt is fine), wear gloves and use an arc welding helmet.
6. Briefly step on the foot pedal and release. The arc will have pulsed and spot welded at the point you had the tungsten electrode.

Notice:
1. Don't step on the pedal for a long time, just step it one time then move off immediately. If you step on the pedal for a long time, this machine will be short circuit, even to burn out inside electricity.
2. This machine is precision equipment, please cherish it.
3. Spark light during the welding is harmful to eyes, please take good protection measures.
4. When you step pedal, don't touch needle or soldering metal.
5. Please do not disassemble the unit without professional guidance.




Features:
  • Platinum can be used for spot welding
  • Welding rapid .K gold gold silver. Steel, for I circle, oval buckle fine precision welding wire, welded directly without solder powder. Joints smooth.
  • Using high-frequency plasma discharge principle, the metal weld puddle formed instantaneously
  • Adjusting output power according to the different sizes of wire
  • The welding work smooth, strong, fast, high efficiency
  • 2 years warranty
Specifications:
  • Color: Red
  • Power supply: 220V 50HZ
  • Power: 400W
  • Ampere for welding: 0.5~50A, continuous adjustable (fluctuation)
  • Weight: about 6.5kg
  • Size: 300*170*225mm
  • Application: All precious metals, precious metals alloy such as gold, silver, platinum, palladium
Package Content:
  • 1 x Welder
  • 1 x Foot Pedal
  • 1 x Cable
  • 1 x Forceps Clamp
  • 1 x Tungsten Needle
You should make sure that the power voltage is suitable for this equipment before using it. The welding output wire should be connected to the screw on the corresponding polarity (The nut should be tightened when output wire is connected to the output pole). When the welder is working, you should use the clip on the output wire clamp the workpiece, close to the tungsten needle. The distance between tungsten needle and the workpiece depends on the size and shape of the workpiece, it is usually between 0.5-1 mm. Set the welding position and move the foot switch, the high-temperature electric arc between the workpiece and the tungsten needle are welding the workpiece. The discharge end of the tungsten needle must be kept sharp before using and during using to maintain a good discharge condition. According to the size of the workpiece, the size of solder joints and technological requirements, you can change the output pulse current intensity to achieve the desired effect (the machine can be welded 0.5-2.5MM). Depending on the size of the workpiece, the size of solder joints and technological requirements, you can change the output pulse current intensity to achieve the desired effect (the machine can be welded 0.5-2.5MM).For example, the potentiometer output pulse current increases in counter- clockwise direction. Otherwise the output pulse current decreases.

Sparkle welder can be used to weld:
1. Precious metal alloys; gold, silver, platinum and palladium
2. Titanium and stainless steel.
3. With some limitations, aluminum, tin and most brass alloys
4. Alloys with different attributes that are incompatible in normal welding
5. Alloys that would oxidize during welding and thus require an inert(Argon) atmosphere

Sparkle welder which use for jeweler:
1. Precisely position parts by tacking with the spot welder
2. Welding of necklaces with a diameter 0.3mm or larger(smaller diameter may melt)
3. Repair metal joints or breaks without removing set stones or pearls
4. Repair heat sensitive metals or metal alloys
5. Repair surface or entry point of a molding of the same alloy

With the inert argon atmosphere, welding can be done without requiring fluxing. The soldering point is smooth and does not require scaling or scale removal.

Installation and testing:
1. Connecting electrode, black wire to black connection (ground/cathode), red wire to red connection (positive /anode).
2. Connect argon gas through the argon gas pressure reducing valve; adjust the gas pressure reading to the minimum
3. Tungsten needle can be sharpened by grinding on the grinding wheel, or with the use of a Fordham flex shaft or dremal tool and an abrasive disk. Note that you should not use a wheel previously used to grind iron/steel as this will contaminate the needle and cause an uneven spark and/or weld results.
4. When installing the tungsten needle, please insure that the needle is approximately 5mm out from the welding head. The diameter of needle should be 0.1mm.

Our machine can only work with small things like necklaces with a diameter including or less than 1.2mm . No more than 1.2mm can work with metal like gold, silver, copper, steel, iron exclude aluminum.

Operation steps:
1. Plug the device into the wall socket and turn it on.
2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material.
3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow.
4. Clamp the object to be welded with the negative ground electrode. You cannot short circuit the machine by having both the tungsten needle and the ground clamp in contact through the work piece at the same time. Do not have the target work piece in direct contact with the tungsten needle. A 0.5mm arc gap is necessary for pulse welder operation. This is the optimum distance for welding.
5. Insure you have arc welding eye protection in place. The arc emits short wave UV radiation that will cause eye retinal burns and skin burns. Cover exposed skin (a shirt is fine), wear gloves and use an arc welding helmet.
6. Briefly step on the foot pedal and release. The arc will have pulsed and spot welded at the point you had the tungsten electrode.

Notice:
1. Don't step on the pedal for a long time, just step it one time then move off immediately. If you step on the pedal for a long time, this machine will be short circuit, even to burn out inside electricity.
2. This machine is precision equipment, please cherish it.
3. Spark light during the welding is harmful to eyes, please take good protection measures.
4. When you step pedal, don't touch needle or soldering metal.
5. Please do not disassemble the unit without professional guidance.




Features:
  • Platinum can be used for spot welding
  • Welding rapid .K gold gold silver. Steel, for I circle, oval buckle fine precision welding wire, welded directly without solder powder. Joints smooth.
  • Using high-frequency plasma discharge principle, the metal weld puddle formed instantaneously
  • Adjusting output power according to the different sizes of wire
  • The welding work smooth, strong, fast, high efficiency
  • 2 years warranty
Specifications:
  • Color: Red
  • Power supply: 220V 50HZ
  • Power: 400W
  • Ampere for welding: 0.5~50A, continuous adjustable (fluctuation)
  • Weight: about 6.5kg
  • Size: 300*170*225mm
  • Application: All precious metals, precious metals alloy such as gold, silver, platinum, palladium
Package Content:
  • 1 x Welder
  • 1 x Foot Pedal
  • 1 x Cable
  • 1 x Forceps Clamp
  • 1 x Tungsten Needle

Shipping Policy

Shipping Fees

All the products are free shipped, and we will not ask for any shipping fees.

Delivery Times

Note: Shipping time is influenced by the COVID-19, the delivery time will put off 3 days! Thanks for your understanding!

After the customer places an order, the order processing time takes 1 to 2 days. So please make sure of entering correct payment and shipping information before checking out.

We adopt the TOLL, Australia Post, Fastway, Direct Freight Express , Parcel freight logistics to ship your orders from the warehouse in Sydney. Delivery generally takes 2 to 6 days. For remote areas the delivery time will take two more days.

About Modification

Once your payment is completed, please inform us by phone or E-mail. And make any modifications before we dispatch your package. The customer will be responsible for all extra fees caused by address alteration if contact is made after the item has been dispatched.

 

Return Policy

We are dedicated to providing our customers with the best online shopping experience, making them 100% satisfied with their purchase. So, if you're not happy with your purchase for any reason, just go through our easy return process.

Claim

This return policy is only applicable to products with a 1-year warranty from our official site but does not pertain in other websites that sell Vevor products.

Returning an Item:

1.Arrived damaged

We provide a free return of the product damaged on the way except artificial damage. When your product is broken, you need to send us the photos of broken product.

2.Missing part

If product parts are missing, we can send you the replacements or partially refund you your money.

3.Wrong item sent

If the product you received is not the one you bought, you could send the product photos to us and we will provide right one for you after verification.

4.Doesn't work or defective

When you received a product that does not work, you can contact our customer service team and we will provide corresponding technical support; if it does still not work, you can ask for a return. When the product is defective, you can ask our customer service to give you technical support or solution, if you repair it by yourself or in local store, we will provide you with some compensation; If you can't repair it by yourself or the local technique person, we will offer you a new item.

Unacceptable Reasons for Free Return:

1.Arrived too late

  •  We apologize for your long waiting. Due to most of our products belonging to heavy ones, the time for packaging is longer than that of the light ones.
  •  If you receive it too late for stock-out, we can make some compensation for you, such as coupon code or partial refund.

 

2.Don't want it

If you have already received the item but changed your mind and no longer want it, you cannot return the item and get a refund. Following situations are also unacceptable: mistaken ordering, changing mind, or price change.

3.Doesn't match the description

If you received the item not the same as the description or image, please give us feedback. Based on the specific reason, we will decide the return freight.

4.Doesn't seem authentic/new

As a premium brand operating for 5 years, our products are all new and genuine, and you can also search for them on other platforms.

5.Without manual or non-standard manual

When you received the package without the manual, please contact our customer service team immediately by email. The electronic version of instructions or video of installation will be sent as soon as possible to your electronic mailbox.

6.Doesn't fit

If the size you received does not fit because of our fault, you can immediately contact us to get a suitable solution.

Unacceptable Reasons for Return:

  • Item was polluted accidentally.
  • Item was damaged by mistake when being used.

 

How to return the product?

Contact our customer service staff by email when you ask for a return, we will send you a return label in electronic version that you need to print and stick on the parcel. You can raise a pickup time or you could wait 1-2 days and then we will arrange for it.

How about after returning items?

  1. We will send you a new item after receiving your parcel.
  2. If you want to get a refund after the product has arrived at our warehouse, you need to contact us.

Note: We reserve all the right to the final interpretation of these terms. If you have any problem, please don't hesitate to contact us!