230v Electric Circular Saw Blade Sharpener Water Injection Grinder Machine
- Category: Hand & Power Tools, Power Saws & Accessories, Power Tools, Saw Blade Sharpener, UP TO $300
Circular carbide saw blade are widely used for cutting aluminum, wood and plastic materials. MF-126 type grinding machine is used for sharpening many sizes and types circular carbide saw blade. If you change the sanding wheel it can also sharp other common saw blade. It is a necessary assistant machine for cutting aluminum, wood and plastic materials.
Method of operation:
First, loosing the fascia, then adjust the angle of grinding blade and fasten.
Second, adjusting of center axle.
- Rotating the center axle to the grinding blade.
- Pushing the center axle to the right.
- Installing the saw blade ,rotate the wheel and decide the position of grinding surface saw teeth.
- Rotating the rotation table to ensure the angle of grinding blade.
- The cross angle between the grinding surface and work surface is about 5.
- Adjusting the saw blade to the grinding position, rotating the positioning frame and fascia.
- Adjusting positioning pin to the proper base of saw teeth and leave gap of grinding quantity, fasten the fixed screw.
Last, when all the parts are fastened, the saw blade supported with hand will be grinded.
Safety remarks:
-
Should match the standard voltage; We must strictly take a good ground, install leakage circuit breakers.
-
The machine should be set in a dry, clean, steady and parallel place.
-
Release the round plat and then adjust the saw blade angle.
-
Check all parts that need locks before operation.
-
After the machine runs well then you can start the work.
-
Take off the electricity after work finishing.
-
Inform the factory before you change the machines.
-
1.base
2.box body
3.end cover
4.rotatary base
5.rotary table base
6.rotary table
7.slide base
8.slide disc
9.table
10.guide nut base
11.guide screw
12.slide block
13.frame
14.board
15.positioning board
16.safe cover
17.press board
18.adjusting bolt
19.upright post
20.long bolt
21.short bolt
22.long handle
23.short handle
24.positioning pin
25.mat cover
26.diamond wheel
27.cover
28.motor
29.rear stuck disc
30.fore stuck disc
31.big pin
32.small pin
33.hand wheel
34.round handle
35.turret handle
36.earth foot
37.adjusting bolt base
38.fastening handle
39.switch
40.screw
41.lirnit pin
42.washe
43.cover
- The machine structure able to work on max diameter φ700mm.
- The specially equipped motor with a good running speed which can have a very good co-operation with the diamond sanding wheel.
- The direction of the sharpening should be paralleled with the diamond sanding wheel, it is better for grinding the back teeth face.
- This machine is designed for sharpening various kinds of carbide tipped saw blades from size 80mm to 700mm.
- Also suitable to grind other material such as plastic, wood, aluminum alloy for different purpose like furniture manufacturing, decoration etc.
- Steel chassis construction
- Grinding wheel angle control with large aluminum knob
- Will hold each blade head position by a position lock
- Extra 2 blade hole adapter.
- X axis feed wheel, stable and very sharp grinding
- Rotary angle mark
- Power: 370W
- Voltage: 230V
- Net Weight: 66.14lbs (30kg)
- Running Speed: 3400RPM
- Adjusting Angle Of The Wheel: ±20°
- Handle Turning Angle: 30 Degrees From Left And 45 Degrees From Right
- Working Diameter: 80-700mm
- Grinding Wheel Size: 4.92" (125mm)
- Bore Size Of Grinding Wheel: 1.26" (32mm)
- Sanding Wheel Dimensions: 4.92" X 0.39" X 1.26"X0.2" X 0.08" (125 X 10 X 32x5x2mm)
- Product Dimension: 30.3"X16.93"X11.81" (770 X 430 X 300mm)
- Package Dimension: 16.93"X16.93"X13.58" (430 X 430 X 345mm)
- 1 x Main machine
- 1 x Standing wheel
- 1 x Saw centering(φ22、φ30、φ25)
- 1 x Saw centering(φ40、φ25.4)
- 1 x Allen wrench
- 1 x Cross
- 1 x Open-end wrench
- 1 x Manual
- 1 x Water tank
Circular carbide saw blade are widely used for cutting aluminum, wood and plastic materials. MF-126 type grinding machine is used for sharpening many sizes and types circular carbide saw blade. If you change the sanding wheel it can also sharp other common saw blade. It is a necessary assistant machine for cutting aluminum, wood and plastic materials.
Method of operation:
First, loosing the fascia, then adjust the angle of grinding blade and fasten.
Second, adjusting of center axle.
- Rotating the center axle to the grinding blade.
- Pushing the center axle to the right.
- Installing the saw blade ,rotate the wheel and decide the position of grinding surface saw teeth.
- Rotating the rotation table to ensure the angle of grinding blade.
- The cross angle between the grinding surface and work surface is about 5.
- Adjusting the saw blade to the grinding position, rotating the positioning frame and fascia.
- Adjusting positioning pin to the proper base of saw teeth and leave gap of grinding quantity, fasten the fixed screw.
Last, when all the parts are fastened, the saw blade supported with hand will be grinded.
Safety remarks:
- Should match the standard voltage; We must strictly take a good ground, install leakage circuit breakers.
- The machine should be set in a dry, clean, steady and parallel place.
- Release the round plat and then adjust the saw blade angle.
- Check all parts that need locks before operation.
- After the machine runs well then you can start the work.
- Take off the electricity after work finishing.
-
Inform the factory before you change the machines.
-
1.base
2.box body
3.end cover
4.rotatary base
5.rotary table base
6.rotary table
7.slide base
8.slide disc
9.table
10.guide nut base
11.guide screw
12.slide block
13.frame
14.board
15.positioning board
16.safe cover
17.press board
18.adjusting bolt
19.upright post
20.long bolt
21.short bolt
22.long handle
23.short handle
24.positioning pin
25.mat cover
26.diamond wheel
27.cover
28.motor
29.rear stuck disc
30.fore stuck disc
31.big pin
32.small pin
33.hand wheel
34.round handle
35.turret handle
36.earth foot
37.adjusting bolt base
38.fastening handle
39.switch
40.screw
41.lirnit pin
42.washe
43.cover
- The machine structure able to work on max diameter φ700mm.
- The specially equipped motor with a good running speed which can have a very good co-operation with the diamond sanding wheel.
- The direction of the sharpening should be paralleled with the diamond sanding wheel, it is better for grinding the back teeth face.
- This machine is designed for sharpening various kinds of carbide tipped saw blades from size 80mm to 700mm.
- Also suitable to grind other material such as plastic, wood, aluminum alloy for different purpose like furniture manufacturing, decoration etc.
- Steel chassis construction
- Grinding wheel angle control with large aluminum knob
- Will hold each blade head position by a position lock
- Extra 2 blade hole adapter.
- X axis feed wheel, stable and very sharp grinding
- Rotary angle mark
- Power: 370W
- Voltage: 230V
- Net Weight: 66.14lbs (30kg)
- Running Speed: 3400RPM
- Adjusting Angle Of The Wheel: ±20°
- Handle Turning Angle: 30 Degrees From Left And 45 Degrees From Right
- Working Diameter: 80-700mm
- Grinding Wheel Size: 4.92" (125mm)
- Bore Size Of Grinding Wheel: 1.26" (32mm)
- Sanding Wheel Dimensions: 4.92" X 0.39" X 1.26"X0.2" X 0.08" (125 X 10 X 32x5x2mm)
- Product Dimension: 30.3"X16.93"X11.81" (770 X 430 X 300mm)
- Package Dimension: 16.93"X16.93"X13.58" (430 X 430 X 345mm)
- 1 x Main machine
- 1 x Standing wheel
- 1 x Saw centering(φ22、φ30、φ25)
- 1 x Saw centering(φ40、φ25.4)
- 1 x Allen wrench
- 1 x Cross
- 1 x Open-end wrench
- 1 x Manual
- 1 x Water tank
Shipping Policy
Note: Shipping time is influenced by the COVID-19, cargoes delivered time put off 3 days!
Shipping Times
We adopt MCS, AU Post,TOLL only ship orders within Australia.
- DELIVERY DAYS: 1-5 DAYS (1-5 DAYS FOR 99% OF AU)
- Processing Time: 1 day
- SHIP FROM AUME WAREHOUSE
About Modification
Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.
The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.
International Purchase
Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.
Return Policy
Every single product is backed by a 12-months Warranty and a 30-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.
If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.
Satisfying Guarantee for Every Purchase
Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 30 days of delivery in original packaging and with proof of purchase from Vevor.
Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.
- All returns must be pre-approved. Unauthorized returns will not be accepted.
- Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
- The same warranty is provided for replaced products as the returned ones.
If you are shipping the product
- Carefully pack the item(s) in original package.
- Stick the shipping label we offered on the outer
- Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
- For assistance on return, please message Vevor Facebook or send a message to: support@vevor.com.au.
