Manual Oil Press Machine Stainless Steel Nuts Seed Oil Expeller Homemade Oil
- Category: Commercial Press Machine, Food Preparation Equipment, Restaurant & Food Service, UP TO $300
Installation:
1. Before each use, thoroughly clean and dry all parts.
2. Start by affixing the frame to the L shaped metal piece. There are three pre-drilled holes on the L shaped metal piece and the frame, they should be aligned and secured with the provided bolts to form one piece.
3. You should then fix the rack to a firm surface. Insert the bolts from the bottom, and fasten them until the frame is firmly secured to the table. You can use the provided round metal pieces to protect your table, and also act as a gap filler if your table edge is not thick enough.
4. The handle: First affix the crank at the bottom of the handle. Then insert the handle to the screw shaft at the end of the press cage and use the bolt to fasten it via the pre-drilled holes. Make sure the handle can rotate effortlessly and smoothly.
5. On the front part of the press cage, you should fasten the press cage cap followed by the terminal adjustment bolt.
6. Fuel bottle: The provided wick should be inserted into the metal cap with the pre-drilled hole. Fill the bottle with kerosene or fuel (It should be 80% full). Leave 0.5cm of the wick outside and put the longer end in the fuel bottle. Place the fuel bottle under the press cage, towards the outside. Secure it with the rubber band so that the fuel bottle stays put and does not move during operation.
7. Plastic oil bottle: Place the empty plastic oil bottle under the opening of the press cage. The bottle will collect the usable oil. If you use your own bottle in the future, make sure it is heat proof.
8. Inlet Plate: Fill the plate with the raw ingredient and let it sit at the top of the press cage.
Please Note:
It is very normal for oil and extracts to flow out of the terminal adjustment bolt at the beginning. You can place a plate or container at the bottom to catch this residue.
If you find the handle is too stiff during operation, you can loosen the terminal adjustment bolt.
If you find there is too much oil in the press cage, you need to tighten the adjustment bolt.
If the ingredient you wish to use is very small, such as sesame seeds, then you can add another oil to the ingredient so that it can go through the press more smoothly.
Freshly pressed oil should be left to cool for 5-7 hours and then consumed within 2-3 days.
It is imperative to clean the machine thoroughly after every use, otherwise the residue in the machine will harden and will affect the next operation of the machine. The machine should also be cleaned before use, if it has been in storage or not used for a while.
The press cage and all metal parts of the machine can get very hot during operation. Please handle with care and wear necessary protective equipment. Do not touch the hot parts with your bare hands. Allow the machine to cool down before cleaning and disassembling.
The round metal caps can be used to protect your table from screw marks/dents. They can also act as a gap filler if your table is too small and the screws do not reach the table.
- Manual oil expeller, give yourself a health and nutritive life
- Adopting high quality stainless steel material, resist to corrosion and durable
- Complete accessories, simple to install
- Suitable for most of the oil content is more than 25% of the oil crops, such as peanut, sunflower seed, tea seed, sesame seed, walnut, olive, coconut oil, flax seed, etc
- Material: Stainless Steel 304
- Color: Silver
- Structure: Mainly Divided Into The Frame, Exploding And Pressing Bolt
- Suitable Raw Materials: Most Of The Oil Content Is More Than 25% Of The Oil Crops
- Size: 270 X 50 X 350 mm Oil Mill Size (Including Packaging)
- Package Size: 375 X 300 X 75 mm
- 1 x Press Cage
- 1 x Screw Shaft
- 1 x Terminal Adjustment Bolt
- 1 x Press Cage Cap
- 1 x Fuel Bottle
- 1 x Crank
- 1 x Funnel
- 1 x Plastic Bottle
- 1 x Brush
- 1 x Wrench
- 1 x Operation Requirement
- All Necessary Assembly Accessories As Photographed
Installation:
1. Before each use, thoroughly clean and dry all parts.
2. Start by affixing the frame to the L shaped metal piece. There are three pre-drilled holes on the L shaped metal piece and the frame, they should be aligned and secured with the provided bolts to form one piece.
3. You should then fix the rack to a firm surface. Insert the bolts from the bottom, and fasten them until the frame is firmly secured to the table. You can use the provided round metal pieces to protect your table, and also act as a gap filler if your table edge is not thick enough.
4. The handle: First affix the crank at the bottom of the handle. Then insert the handle to the screw shaft at the end of the press cage and use the bolt to fasten it via the pre-drilled holes. Make sure the handle can rotate effortlessly and smoothly.
5. On the front part of the press cage, you should fasten the press cage cap followed by the terminal adjustment bolt.
6. Fuel bottle: The provided wick should be inserted into the metal cap with the pre-drilled hole. Fill the bottle with kerosene or fuel (It should be 80% full). Leave 0.5cm of the wick outside and put the longer end in the fuel bottle. Place the fuel bottle under the press cage, towards the outside. Secure it with the rubber band so that the fuel bottle stays put and does not move during operation.
7. Plastic oil bottle: Place the empty plastic oil bottle under the opening of the press cage. The bottle will collect the usable oil. If you use your own bottle in the future, make sure it is heat proof.
8. Inlet Plate: Fill the plate with the raw ingredient and let it sit at the top of the press cage.
Please Note:
It is very normal for oil and extracts to flow out of the terminal adjustment bolt at the beginning. You can place a plate or container at the bottom to catch this residue.
If you find the handle is too stiff during operation, you can loosen the terminal adjustment bolt.
If you find there is too much oil in the press cage, you need to tighten the adjustment bolt.
If the ingredient you wish to use is very small, such as sesame seeds, then you can add another oil to the ingredient so that it can go through the press more smoothly.
Freshly pressed oil should be left to cool for 5-7 hours and then consumed within 2-3 days.
It is imperative to clean the machine thoroughly after every use, otherwise the residue in the machine will harden and will affect the next operation of the machine. The machine should also be cleaned before use, if it has been in storage or not used for a while.
The press cage and all metal parts of the machine can get very hot during operation. Please handle with care and wear necessary protective equipment. Do not touch the hot parts with your bare hands. Allow the machine to cool down before cleaning and disassembling.
The round metal caps can be used to protect your table from screw marks/dents. They can also act as a gap filler if your table is too small and the screws do not reach the table.
Features:
- Manual oil expeller, give yourself a health and nutritive life
- Adopting high quality stainless steel material, resist to corrosion and durable
- Complete accessories, simple to install
- Suitable for most of the oil content is more than 25% of the oil crops, such as peanut, sunflower seed, tea seed, sesame seed, walnut, olive, coconut oil, flax seed, etc
- Material: Stainless Steel 304
- Color: Silver
- Structure: Mainly Divided Into The Frame, Exploding And Pressing Bolt
- Suitable Raw Materials: Most Of The Oil Content Is More Than 25% Of The Oil Crops
- Size: 270 X 50 X 350 mm Oil Mill Size (Including Packaging)
- Package Size: 375 X 300 X 75 mm
- 1 x Press Cage
- 1 x Screw Shaft
- 1 x Terminal Adjustment Bolt
- 1 x Press Cage Cap
- 1 x Fuel Bottle
- 1 x Crank
- 1 x Funnel
- 1 x Plastic Bottle
- 1 x Brush
- 1 x Wrench
- 1 x Operation Requirement
- All Necessary Assembly Accessories As Photographed
Shipping Policy
Note: Shipping time is influenced by the COVID-19, cargoes delivered time put off 3 days!
Shipping Times
We adopt MCS, AU Post,TOLL only ship orders within Australia.
- DELIVERY DAYS: 1-5 DAYS (1-5 DAYS FOR 99% OF AU)
- Processing Time: 1 day
- SHIP FROM AUME WAREHOUSE
About Modification
Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.
The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.
International Purchase
Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.
Return Policy
Every single product is backed by a 12-months Warranty and a 30-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.
If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.
Satisfying Guarantee for Every Purchase
Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 30 days of delivery in original packaging and with proof of purchase from Vevor.
Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.
- All returns must be pre-approved. Unauthorized returns will not be accepted.
- Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
- The same warranty is provided for replaced products as the returned ones.
If you are shipping the product
- Carefully pack the item(s) in original package.
- Stick the shipping label we offered on the outer
- Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
- For assistance on return, please message Vevor Facebook or send a message to: support@vevor.com.au.