5in1 Lcd Separator Machine Plate Screen Glass Repair Cell Phone Iphone Samsung
Rated 3.5/5 based on 11 customer reviews

5in1 Lcd Separator Machine Plate Screen Glass Repair Cell Phone Iphone Samsung

Available: Out of Stock
Product SKU: SJPMWXFLJ00000001V3
$192.99 AUD
Successful pre-order.Thanks for contacting us!
5 in 1 frame machine consists of heated plate, a-frame separator, manual vacuum separator, glue remover and frame pressing laminator. This machine set can help separate the cell phone’s touch screen from LCD, or from front glass lens. There is no need any clamps to press the LCD screen due to the built-in vacuum pump, it is much more convenient for your mobile phone repairing. Our machine is compatible with all mobile phones 6P and below, used to separate broken glass from lens, touch screen and LCD display assembly. You can easily remove the damaged glass and replace it reducing cost and wait time. The heating plate is made of integrative non-pressurized aluminum-alloy with well-distributed heat conduction which is not distorted under high temperature. By using this machine, you can separate the broken glass from the LCD display assembly much easy. The unit heats up the screen assembly to loosen the glue, so that you can remove it with a molybdenum cutting wire. With a LCD dispay, you may adjust the temperature much more accurate and easier.

Middle frame separation steps:
1. Turn on the thermostat switch of heated plate, then set the temperature to 80°C.
2. Use a sealed bag, make the adhesive gap around and back of the assembly coated with whellote gas, then seal the bag.
3. Take out the assembly after 5min.
4. Heat it on the heated plate about 20s, turn on the corresponding mould switch, press the assembly on the suction mould.
5. After being sucked, separating the middle frame slowly by hand.


Screen separation steps:
1. Turn on the thermostat switch of heated plate, then set the temperature to 80°C.
2. Haul back the lower plate, lock the screw tightly(prevent sliding). Put the silicone pad on the heated plate holes to holes, then place the screen on it.
3. Turn on the suction switch, the screen will be sucked tightly. When the screen reaches an appropriate temperature, start to separate the screen with a steel wire.

Glue removing steps:
1. Loose the three screws of the blade groove, put in the blade and screw it.
2. Turn on the thermostat switch of glue remover on the right side, set the temperature to 180°C.
3. Put the silicone pad on the heated plate, when it reaches to required temperature, put into the screen with the flex cable inby.
4. Push into the screen, keep the height of the blade and the screen be the same, then move the screen to remove the glue.


Frame press and laminating steps:
1. Turn on the thermostat switch on the right mould, set the temperature to 180°C.
2. Choose a lower mould, put the lower mould into the plate(the groove of the mould keep downward), push the lower mould to align with the upper mould, then fix the screws behind the lower mould.
3. After installing the frame of the screen, put it into the lower mould in the right direction. Put the lower mould on the plate in the right position, the upper mould press it for 6-10s, then take out the screen.
4. When laminating for iPhone6(4.7), it need to install the upper mould.

Note:
  • Remove the blade when not removing glue to prevent from hurting by it.
  • We have 220V and 110V item on sale, please tell us what kind of item do you need, or we will send the item out according to your own country’s voltage.


Features:
  • Multiple functions combined in one, it can deal with many problems just with 1 machine, economical assistant tool for smart phone repair.
  • The application of advanced glue removing technology, this machine can remove glue effectively.
  • 2 small pillars on the sides of operating plate, it can avoid the damage of steel wires when separating screen and it is helpful for operating safety.
  • Suitable for iPhone/Samsung phones repair.
  • The shell of vacuum LCD Separator is metal. And it's better than back light vacuum LCD Separator.
  • The vacuum LCD separator equip with four bearings. It's more convenient when separating.
  • The LCD separator equip with anti-slip mounting seats. It makes your work smoothly and decreases the opportunity of damaging LCD assembly.
  • This machine set can help separate the cell phone’s touch screen from LCD, or from front glass lens.
  • Come with 5 phone moulds: upper mold for iPhone6, lower molds for iPhone4/5/6(4.7)/6(5.5).
Specifications:
  • Material: Coated Iron Plate + Aluminum Alloy
  • Plug Type: AU
  • Power Supply: AC100-240V
  • Power: 500W
  • Suitable For Screens: Less Than 7”, Samsung, Sony, HTC, iPhone, Etc.
  • Item Weight: 19kg / 41.9lbs
  • Heating Plate Dimension: 320mm X 250mm X 415mm
  • Package Size: 39 X 38 X 46cm / 15.3 X 14.9 X 18.1in
Package Content:
  • 1 × Machine
  • 1 × Power Line
  • 1 × Silicone Pad
  • 5 × Moulds
  • 3 × Screw Drivers
5 in 1 frame machine consists of heated plate, a-frame separator, manual vacuum separator, glue remover and frame pressing laminator. This machine set can help separate the cell phone’s touch screen from LCD, or from front glass lens. There is no need any clamps to press the LCD screen due to the built-in vacuum pump, it is much more convenient for your mobile phone repairing. Our machine is compatible with all mobile phones 6P and below, used to separate broken glass from lens, touch screen and LCD display assembly. You can easily remove the damaged glass and replace it reducing cost and wait time. The heating plate is made of integrative non-pressurized aluminum-alloy with well-distributed heat conduction which is not distorted under high temperature. By using this machine, you can separate the broken glass from the LCD display assembly much easy. The unit heats up the screen assembly to loosen the glue, so that you can remove it with a molybdenum cutting wire. With a LCD dispay, you may adjust the temperature much more accurate and easier.

Middle frame separation steps:
1. Turn on the thermostat switch of heated plate, then set the temperature to 80°C.
2. Use a sealed bag, make the adhesive gap around and back of the assembly coated with whellote gas, then seal the bag.
3. Take out the assembly after 5min.
4. Heat it on the heated plate about 20s, turn on the corresponding mould switch, press the assembly on the suction mould.
5. After being sucked, separating the middle frame slowly by hand.


Screen separation steps:
1. Turn on the thermostat switch of heated plate, then set the temperature to 80°C.
2. Haul back the lower plate, lock the screw tightly(prevent sliding). Put the silicone pad on the heated plate holes to holes, then place the screen on it.
3. Turn on the suction switch, the screen will be sucked tightly. When the screen reaches an appropriate temperature, start to separate the screen with a steel wire.

Glue removing steps:
1. Loose the three screws of the blade groove, put in the blade and screw it.
2. Turn on the thermostat switch of glue remover on the right side, set the temperature to 180°C.
3. Put the silicone pad on the heated plate, when it reaches to required temperature, put into the screen with the flex cable inby.
4. Push into the screen, keep the height of the blade and the screen be the same, then move the screen to remove the glue.


Frame press and laminating steps:
1. Turn on the thermostat switch on the right mould, set the temperature to 180°C.
2. Choose a lower mould, put the lower mould into the plate(the groove of the mould keep downward), push the lower mould to align with the upper mould, then fix the screws behind the lower mould.
3. After installing the frame of the screen, put it into the lower mould in the right direction. Put the lower mould on the plate in the right position, the upper mould press it for 6-10s, then take out the screen.
4. When laminating for iPhone6(4.7), it need to install the upper mould.

Note:
  • Remove the blade when not removing glue to prevent from hurting by it.
  • We have 220V and 110V item on sale, please tell us what kind of item do you need, or we will send the item out according to your own country’s voltage.


Features:
  • Multiple functions combined in one, it can deal with many problems just with 1 machine, economical assistant tool for smart phone repair.
  • The application of advanced glue removing technology, this machine can remove glue effectively.
  • 2 small pillars on the sides of operating plate, it can avoid the damage of steel wires when separating screen and it is helpful for operating safety.
  • Suitable for iPhone/Samsung phones repair.
  • The shell of vacuum LCD Separator is metal. And it's better than back light vacuum LCD Separator.
  • The vacuum LCD separator equip with four bearings. It's more convenient when separating.
  • The LCD separator equip with anti-slip mounting seats. It makes your work smoothly and decreases the opportunity of damaging LCD assembly.
  • This machine set can help separate the cell phone’s touch screen from LCD, or from front glass lens.
  • Come with 5 phone moulds: upper mold for iPhone6, lower molds for iPhone4/5/6(4.7)/6(5.5).
Specifications:
  • Material: Coated Iron Plate + Aluminum Alloy
  • Plug Type: AU
  • Power Supply: AC100-240V
  • Power: 500W
  • Suitable For Screens: Less Than 7”, Samsung, Sony, HTC, iPhone, Etc.
  • Item Weight: 19kg / 41.9lbs
  • Heating Plate Dimension: 320mm X 250mm X 415mm
  • Package Size: 39 X 38 X 46cm / 15.3 X 14.9 X 18.1in
Package Content:
  • 1 × Machine
  • 1 × Power Line
  • 1 × Silicone Pad
  • 5 × Moulds
  • 3 × Screw Drivers

Shipping Policy

Note: Shipping time is influenced by the COVID-19, cargoes delivered time put off 3 days!

Shipping Times

We adopt  MCS, AU Post,TOLL only ship orders within Australia.

  • DELIVERY DAYS: 1-5 DAYS (1-5 DAYS FOR 99% OF AU)
  • Processing Time: 1 day
  • SHIP FROM AUME WAREHOUSE

     

    About Modification

    Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.

    The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.

     

    International Purchase

    Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.

     

     

    Return Policy

    Every single product is backed by a 12-months Warranty and a 30-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.

    If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.

     

    Satisfying Guarantee for Every Purchase

    Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 30 days of delivery in original packaging and with proof of purchase from Vevor.

     

    Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.

     

    1. All returns must be pre-approved. Unauthorized returns will not be accepted.
    2. Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
    3. The same warranty is provided for replaced products as the returned ones.

     

    If you are shipping the product

    1. Carefully pack the item(s) in original package.
    2. Stick the shipping label we offered on the outer
    3. Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
    4. For assistance on return, please message Vevor Facebook or send a message to: support@vevor.com.au.