2180w Diamond Core Drill Concrete Machine Wet Drilling With Stand & Drill Bits
Rated 3.5/5 based on 11 customer reviews

2180w Diamond Core Drill Concrete Machine Wet Drilling With Stand & Drill Bits

Available: Out of Stock
Product SKU: Z1Z-160SZJ0000001V3
$267.99 AUD
Successful pre-order.Thanks for contacting us!
Our core drilling machine combines functionality and versatility in one device. It is ideal for lighter drilling work.

Installation:

First, install the screw connecting the stand and the pedestal. Before use the drill, you need to fix it.
1. Remove the two screws on the back of the stand;
2. Seperate the stand and the pedestal;
3. Rotate the pedesta 180° and install the screws.
4. Install completed

Fix the driller:

Here are two ways
1.Using expansion link
Choose a hollow tube according to the height of the place which need to be drilled. Put one end of the tube against the adjustable screw rod. And turn the rod reversely to fix the driller tightly, expansion bolts are not needed.
2.Using ecpansion bolt
Make a hole on the wall or the groud and install the bolt;
Expand the bolt;
Install the screw rod and the stand. Then tighten the nut.
Install drill bit
Before installing, you need to smear some grease on the drill end thread in order to discharge easily. After instlling, you need to run the driller at an idle state at first.
Attention: Before you install or remove the drill bot, you must be sure the drill is powered off. Before running, the drill must be connected with clean cold water.

Here are the ways to inject water:

1. Using tap water: Connecting the tap and the machine with the injecting hose.
2. Hanging a bucket over the drill
3. Using water pump
4.Drilling
Start the drill at an idle state. Then open the water tap. When there is water flowing from the drill, you can start drilling. At first, you need to drill slowly and increase strength gradually. After you drill deeper than 5mm, you can increase your push strength. If the drill's rotating speed decrease, than proves that the drill is overloaded. Then you need to decrease the push strength, avoiding the drill being stuck. If there is smoke coming out, you must pull out the drill right away and start to drill after a while, avoiding the engine being burn down.
5.Material being drilled
When drilling reinforced concrete, current increases and the drill will vibrate. Therefore, you need to decrease pushing strength but the decreasing amplitude should not be too big. Otherwise, the effiency will be affected and the drill bit will be worn more badly. When drilling reinforced concrete containing little grains of sand and small stones, the drill may be overloaded suddenly and the drill be powered off automatically. At this time, you need to pull out the drill right away and clean the hole you drilled before you start again. When you drill woof board and thick pitch, you also need to decrease pushing and drill slowly.
6.Taking out drill core
When you are going yo drill through the board or wal, you need to slow down, avoiding the drill bit being stuck. If the drill bit is stuck, you need to power off the drill immediately pull out the bit and clean it. Fetch out the drill core. Install the drill bit and start again.
Attention: You should be careful when taking out the drill bit, noting damaing it.
7.The drill vibrate
The drill vibrate when it is working.It may be because the distance between the racks connecting the lifting body and the stand is too big. Then you need to tighten the screws to adjust the distance. At the same time, you need to make sure that the pedestal and the stand is connected firmly.

Application:

This drill can be used on brick, stone, reinforced concrete, rock, and fireproof materials.
Features:
  • Water connection with hose approx. 4 meters
  • Overload protection / slip clutch
  • Aluminum base support
  • Use from -25 ° C
  • Drill bit ? 10,8 cm / 35 cm long
  • 1/2 "BSP threaded connection for drill bits
  • 55 mm mandrel on stand for quick release
  • The biggest drill dual purpose
  • 2180W infinitely variable speeds
  • Non water seal cage reduce maintenance costs
  • Aluminum alloy material ligher and steadier
  • Max. drilling diameter 160mm
  • Suitable for sampling concrete, cement, brick, bituminous pavement and block
Specifications:
  • Rated input power: 2180W
  • Rated voltage: 240V
  • Rated frequency: 50Hz
  • Thread Adaptor Size: 32 mm
  • Drilling Diameter Range: 20-160mm
  • Drill bit: 108mm
  • No-load speed: 0-1600 r/min
  • Integrated FI (residual current circuit breaker): 10mA
  • Water hose length: approx. 4 meters, inside ? 1cm
  • Operation Lever: Spring Self-Centring
  • Gear System: Ball Bearing
  • Safety Switch: Earth Leakage Circuit Breaker (SAA Approved)
  • Stand Height: 80cm
  • Drilling distance: approx. 48cm
  • Packing size: 75X20X25cm
  • Material Suitability: Masonry and Concrete Varieties
  • G.W.: 18kg


Package Content:
  • 1 X 2180W Diamond Core Drill
  • 1 X Drill Bit(Φ108mm)
  • 1 X Ring Spanner
  • 1 X Monkey Wrench
  • 1 X Hose
  • 1 X Faucet Interface
  • 5 X Expansion Screws
  • 2 X Carbon Brushes

Our core drilling machine combines functionality and versatility in one device. It is ideal for lighter drilling work.

Installation:

First, install the screw connecting the stand and the pedestal. Before use the drill, you need to fix it.
1. Remove the two screws on the back of the stand;
2. Seperate the stand and the pedestal;
3. Rotate the pedesta 180° and install the screws.
4. Install completed

Fix the driller:

Here are two ways
1.Using expansion link
Choose a hollow tube according to the height of the place which need to be drilled. Put one end of the tube against the adjustable screw rod. And turn the rod reversely to fix the driller tightly, expansion bolts are not needed.
2.Using ecpansion bolt
Make a hole on the wall or the groud and install the bolt;
Expand the bolt;
Install the screw rod and the stand. Then tighten the nut.
Install drill bit
Before installing, you need to smear some grease on the drill end thread in order to discharge easily. After instlling, you need to run the driller at an idle state at first.
Attention: Before you install or remove the drill bot, you must be sure the drill is powered off. Before running, the drill must be connected with clean cold water.

Here are the ways to inject water:

1. Using tap water: Connecting the tap and the machine with the injecting hose.
2. Hanging a bucket over the drill
3. Using water pump
4.Drilling
Start the drill at an idle state. Then open the water tap. When there is water flowing from the drill, you can start drilling. At first, you need to drill slowly and increase strength gradually. After you drill deeper than 5mm, you can increase your push strength. If the drill's rotating speed decrease, than proves that the drill is overloaded. Then you need to decrease the push strength, avoiding the drill being stuck. If there is smoke coming out, you must pull out the drill right away and start to drill after a while, avoiding the engine being burn down.
5.Material being drilled
When drilling reinforced concrete, current increases and the drill will vibrate. Therefore, you need to decrease pushing strength but the decreasing amplitude should not be too big. Otherwise, the effiency will be affected and the drill bit will be worn more badly. When drilling reinforced concrete containing little grains of sand and small stones, the drill may be overloaded suddenly and the drill be powered off automatically. At this time, you need to pull out the drill right away and clean the hole you drilled before you start again. When you drill woof board and thick pitch, you also need to decrease pushing and drill slowly.
6.Taking out drill core
When you are going yo drill through the board or wal, you need to slow down, avoiding the drill bit being stuck. If the drill bit is stuck, you need to power off the drill immediately pull out the bit and clean it. Fetch out the drill core. Install the drill bit and start again.
Attention: You should be careful when taking out the drill bit, noting damaing it.
7.The drill vibrate
The drill vibrate when it is working.It may be because the distance between the racks connecting the lifting body and the stand is too big. Then you need to tighten the screws to adjust the distance. At the same time, you need to make sure that the pedestal and the stand is connected firmly.

Application:

This drill can be used on brick, stone, reinforced concrete, rock, and fireproof materials.
Features:
  • Water connection with hose approx. 4 meters
  • Overload protection / slip clutch
  • Aluminum base support
  • Use from -25 ° C
  • Drill bit ? 10,8 cm / 35 cm long
  • 1/2 "BSP threaded connection for drill bits
  • 55 mm mandrel on stand for quick release
  • The biggest drill dual purpose
  • 2180W infinitely variable speeds
  • Non water seal cage reduce maintenance costs
  • Aluminum alloy material ligher and steadier
  • Max. drilling diameter 160mm
  • Suitable for sampling concrete, cement, brick, bituminous pavement and block
Specifications:
  • Rated input power: 2180W
  • Rated voltage: 240V
  • Rated frequency: 50Hz
  • Thread Adaptor Size: 32 mm
  • Drilling Diameter Range: 20-160mm
  • Drill bit: 108mm
  • No-load speed: 0-1600 r/min
  • Integrated FI (residual current circuit breaker): 10mA
  • Water hose length: approx. 4 meters, inside ? 1cm
  • Operation Lever: Spring Self-Centring
  • Gear System: Ball Bearing
  • Safety Switch: Earth Leakage Circuit Breaker (SAA Approved)
  • Stand Height: 80cm
  • Drilling distance: approx. 48cm
  • Packing size: 75X20X25cm
  • Material Suitability: Masonry and Concrete Varieties
  • G.W.: 18kg


Package Content:
  • 1 X 2180W Diamond Core Drill
  • 1 X Drill Bit(Φ108mm)
  • 1 X Ring Spanner
  • 1 X Monkey Wrench
  • 1 X Hose
  • 1 X Faucet Interface
  • 5 X Expansion Screws
  • 2 X Carbon Brushes

Shipping Policy

Shipping Fees

All the products are free shipped; but some remote areas may require extra fees.

Delivery Times

Note: Shipping time is influenced by the COVID-19, the delivery time will put off 3 days! Thanks for your understanding!

After the customer places an order, the order processing time takes 1 to 2 days. So please make sure of entering correct payment and shipping information before checking out.

We adopt the TOLL, Australia Post, Fastway, Direct Freight Express , Parcel freight logistics to ship your orders from the warehouse in Sydney. Delivery generally takes 2 to 6 days. For remote areas the delivery time will take two more days.

About Modification

Once your payment is completed, please inform us by phone or E-mail. And make any modifications before we dispatch your package. The customer will be responsible for all extra fees caused by address alteration if contact is made after the item has been dispatched.

 

Return Policy

We are dedicated to providing our customers with the best online shopping experience, making them 100% satisfied with their purchase. So, if you're not happy with your purchase for any reason, just go through our easy return process.

Claim

This return policy is only applicable to products with a 1-year warranty from our official site but does not pertain in other websites that sell Vevor products.

Returning an Item:

1.Arrived damaged

We provide a free return of the product damaged on the way except artificial damage. When your product is broken, you need to send us the photos of broken product.

2.Missing part

If product parts are missing, we can send you the replacements or partially refund you your money.

3.Wrong item sent

If the product you received is not the one you bought, you could send the product photos to us and we will provide right one for you after verification.

4.Doesn't work or defective

When you received a product that does not work, you can contact our customer service team and we will provide corresponding technical support; if it does still not work, you can ask for a return. When the product is defective, you can ask our customer service to give you technical support or solution, if you repair it by yourself or in local store, we will provide you with some compensation; If you can't repair it by yourself or the local technique person, we will offer you a new item.

Unacceptable Reasons for Free Return:

1.Arrived too late

  •  We apologize for your long waiting. Due to most of our products belonging to heavy ones, the time for packaging is longer than that of the light ones.
  •  If you receive it too late for stock-out, we can make some compensation for you, such as coupon code or partial refund.

 

2.Don't want it

If you have already received the item but changed your mind and no longer want it, you cannot return the item and get a refund. Following situations are also unacceptable: mistaken ordering, changing mind, or price change.

3.Doesn't match the description

If you received the item not the same as the description or image, please give us feedback. Based on the specific reason, we will decide the return freight.

4.Doesn't seem authentic/new

As a premium brand operating for 5 years, our products are all new and genuine, and you can also search for them on other platforms.

5.Without manual or non-standard manual

When you received the package without the manual, please contact our customer service team immediately by email. The electronic version of instructions or video of installation will be sent as soon as possible to your electronic mailbox.

6.Doesn't fit

If the size you received does not fit because of our fault, you can immediately contact us to get a suitable solution.

Unacceptable Reasons for Return:

  • Item was polluted accidentally.
  • Item was damaged by mistake when being used.

 

How to return the product?

Contact our customer service staff by email when you ask for a return, we will send you a return label in electronic version that you need to print and stick on the parcel. You can raise a pickup time or you could wait 1-2 days and then we will arrange for it.

How about after returning items?

  1. We will send you a new item after receiving your parcel.
  2. If you want to get a refund after the product has arrived at our warehouse, you need to contact us.

Note: We reserve all the right to the final interpretation of these terms. If you have any problem, please don't hesitate to contact us!

    Customer Reviews

    Based on 15 reviews
    60%
    (9)
    40%
    (6)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    D
    D.
    Great deal for the money.
    R
    R.A.
    Equipo robusto
    S
    S.B.
    great customer service!
    B
    B.
    Good
    C
    C.B.
    Did the job.